B7ZA, M7ZA, B7VA, B7XA, B7YA, B7TA 1997-02 4 Speed

When a B7ZA automatic transmission rebuild stalls because the parts order comes in short, the problem is usually a kit that did not account for all three steel clutch specifications...

An electrical fault in the shift circuit shows up as a stored code, a harsh shift or a gear the unit will not select.B7XA solenoid new shift linear Accor.d v6....

When the clutch pack module in a 4-speed automatic transmission shows wear, shifts become sluggish or the unit slips under load, and replacing the module with a dimensionally correct part...

B7TA Overhaul Kit for B7TA automatic transmissions, 1996 to 2002. Includes gasket and seal set for a complete overhaul. 1 pieces in 1 components. Overhaul Kit for B7TA - replacement...

The piston is what converts line pressure into clamping force, so a leaking one makes every other repair pointless.B7VA bonded piston kit 2 piston. This restores the piece that turns...

When a clutch pack starts slipping, the steels are often the first parts to show heat damage even when the frictions still look serviceable.B7VA steel module. The plates are produced...

B7XA Overhaul Kit for B7TA automatic transmissions, 1996 to 2002. Includes gasket and seal set for a complete overhaul. 1 pieces in 1 components. Overhaul Kit for B7XA - replacement...

This kit is built around a single focused purpose: delivering all 20 friction plates needed to service the 1st, 2nd, 3rd, and 4th clutch packs in B7ZA, B7XA, and M7ZA...

Debris in the valve body holds a valve open just long enough to burn the pack it feeds.B7ZA press reg conv charge 4-spd 6-cyl 3-shaft .388 cpv valve (Improved) kit....

Dirty fluid takes out solenoids first because the internal tolerances are the tightest in the unit.BAXA solenoid shift brown. The part is produced to the control specification of the circuit...

When the controller commands a shift and nothing happens, the circuit is usually the culprit, not the clutch.BAXA solenoid shift a (black). This component restores the commanded response the valve...

A solenoid that sticks intermittently throws a code the customer never reproduces for the shop.B6VA 4s 5s switch 2 3 pres 33 psi(black). The part is produced to the control...

Dirty fluid takes out solenoids first because the internal tolerances are the tightest in the unit.B6VA sensor speed Accor.d Odysse.y 2001. It is built to the resistance and flow the...

When the controller commands a shift and nothing happens, the circuit is usually the culprit, not the clutch.B6VA solenoid lock up. The part is produced to the control specification of...

Shift timing lives in the valve body, and worn bores put that timing out of range.B7ZA 4 5-spd tc check valve (valve sleeve spring shim) various. Bores, valves and plate...

Sticking valves are why a unit shifts correctly cold and misbehaves once it warms up.B6VA 4 5 spd converter over heating fix conv charge press regulator valve most. This valve...

A teardown that finds one worn component has almost always found the first of several.M7ZA B7ZA M7ZA B7VA B7XA B7YA B7TA 4 Speed Clutch Set. Everything in this kit belongs...

Sourcing a rebuild one part at a time means the job sits on the bench while the last piece ships.M7ZA 4 SPEED Clutch Set. This kit puts the whole wear...

B7TA B7XA B7YA B7VA M7ZA Overhaul Kit for B7TA automatic transmissions, 1999 and later. Includes gasket and seal set for a complete overhaul. 1 pieces in 1 components. Overhaul Kit...

An electrical fault in the shift circuit shows up as a stored code, a harsh shift or a gear the unit will not select.B7XA solenoid lockup. The unit meets the...

This is a single master rebuild kit for the B7XA automatic transmission, assembled and verified at the REMCO facility before it ships. What sets this kit apart is that it...

Apply pressure that reads correct at the port can still be lost at the piston.B7XA bonded 1st clutch 02 retainer. These pistons return the pack to the apply rate it...

Bonded pistons fail at the bond line, and the failure is invisible on the bench.M7ZA bonded 2nd clutch 98-02 retainer. Each piston is produced to the bore and travel of...

Hairline cracks in a piston do not show until the circuit is under pressure on the road.B7VA Piston bonded 1st clu 2nd clu 99-01 retainer. Each piston is produced to...

An Automatic Transmission Filter that has done its job is full, and full means the pump is working against it on every start.B7XA Automatic Transmission Filter. This Automatic Transmission Filter...

When the clutch pack in a 4-speed automatic transmission starts slipping or refuses to hold, one worn or warped steel plate can be the root cause, and replacing it with...

Fluid on the case is the visible half of the problem; the other half is the pressure that never reached the clutch.B7VA bell housing to case gasket. Each seal is...